The graph bars on the material properties cards below compare ASTM grade HK steel to:cast austenitic stainless steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.
Chemical Compositions & Mechanical Properties - Unified Chemical-Compositions-Mechanical-Properties Common Grade UNS Number Composition(s), % C Si Mn P (max) S (max) Ni Cr Mo Others TP 304 S30400 <=0.08 <=0.75 <=2.00 0.04 0.03 8.00-11.00 18.00-20.00 TP 304 H S30409
CHEMICAL COMPOSITION - PERCENT C max P max MECHANICAL PROPERTIES NOMINAL THICKNESS/ DIA min TENSILE STRENGTH N/mm2 (Kgf/mm2) min YIELD STRESS N/mm2 (Kgf/mm2) min ELONGATION percent min GL 5.65/A S max Structural Steel 0.25 0,20/0.35 0.055 Standard Quality (Where so each required) Plates, Sections- Below 6 *Bend test only shall be required
RA330 vs 309/310 - Rolled Alloysalloys using the higher nickel grade 82 weld wire. Rolled Alloys stocks a complete range of RA330 products including plate, sheet, various types of bar, pipe and welding consumables. Chemical Composition, % UNS W.Nr Ni Cr Fe Si C Mn RA330® N08330 1.4886 35 19 43 1.25 0.05 1.5 310 S31008 1.4845 20 25 52 0.5 0.05 1.6
SAE steel gradesType 420Cutlery Grade martensitic; similar to the Brearley's original rustless steel. Excellent polishability. Type 430decorative, e.g., for automotive trim; ferritic. Good formability, but with reduced temperature and corrosion resistance. Type 439ferritic grade, a higher grade version of 409 used for catalytic converter exhaust sections.
SAF Duplex 2205 Stainless Steel (UNS S32205 S31803) Alloy Material. SAF Duplex 2205 stainless steel (UNS S32205 formerly known as UNS S31803 and commonly known as alloy 2205) has a mixed microstructure of austenite and ferrite, and is a two-phase alloy based on the Fe-Cr-Ni series. Alloy 2205 material has lower nickel and molybdenum contents than austenitic stainless steel and have
Stainless Steel - Grade 316 (UNS S31600)
Chemical FormulaKey PropertiesMechanical PropertiesGrade Specification ComparisonCorrosion ResistanceHeat ResistanceHeat TreatmentWeldingMachiningDual CertificationApplicationsFe, <0.03% C, 16-18.5% Cr, 10-14% Ni, 2-3% Mo, <2% Mn, <1% Si, <0.045% P, <0.03% SGrade 316 is the standard molybdenum-bearing grade, second in importance to 304 amongst the austenitic stainless steels. The molybdenum gives 316 better overall corrosion resistant properties than Grade 304, particularly higher resistance to pitting and crevice corrosion in chloride environments. It has excellent forming and welding characteristics. It is readily brake or roll formed into a variety of parts forSG Iron Casting Grades and StandardsThe followings are the grade requirement to the chemical components and physical properties, and also grade comparison chart. At the same time, we listed the main content of material standards using in USA, China, Germany, Europe and International. Please notice that the chemical components are only a reference, not a strict standard to the
Stainless Steel 304, SS 310S, SS 316 Chemical CompositionGet In Touch. SHOP NO G/3; HARARWALA BUILDING COMPOUND; ARDESHIRDADY STREET; S.V.P ROAD; MUMBAI-400 004, INDIA. Tel No.:+91-22-61905600 (100 Lines) Email :[email protected]
Type 316the second most common grade (after 304); for food and surgical stainless steel uses; alloy addition of molybdenum prevents specific forms of corrosion. It is also known as marine grade stainless steel due to its increased resistance to chloride corrosion compared to type 304. 316 is often used for building nuclear reprocessing plants.
Stainless Steels AISI 304 vs AISI 316 - the Difference Therefore, both grade 304 stainless steel and grade 316 conform to the American standard. The European equivalents are 1.4301 and 1.4401, respectively. You can probably see why people usually choose to go with American standards here. But what do the grades of stainless steel mean? Basically, they indicate the steels structure.
The Global Leader in Specialty MetalsChemical Composition, % Cr Ni Si Mn N C Ce Fe RA 253 MA® UNS S30815 21.0 11.0 1.7 0.6 0.17 0.08 0..04 balance 310 UNS S31008 25.0 20.0 0.5 1.6 0.05 balance Creep-Rupture Properties Creep Test:Ring specimens subjected to a temperature of 1800°F under the stress of their own weight for total of 32 hours. RA 253 MA® vs 310 A Quick
CHEMICAL COMPOSITION Type 410* Type 420** Type 425 Mod Type 440A Element in Weight Percent Carbon Manganese Silicon Chromium Molybdenum Nickel Sulfur Phosphorus 0.15 max 1.00 max 1.00 max 11.50-13.50 -- 0.50 max 0.03 max 0.04 max 0.15-0.40 1.00 max 1.00 max 12.00-14.00 --- 0.50 max 0.03 max 0.04 max310 / 310S Stainless Steel (1.4845) Data Sheet Grade 310 / 310S stainless steel (1.4845) is one of the most widely used grades of heat resistant stainless steel supplied into numerous industry sectors. The key properties of this material are its high chromium and medium nickel content making its resistance to oxidation, sulfidation and other forms of hot corrosion its main characteristics.